ASTM D – Tensile Properties of Yarns by the Single Strand Method. Scope: This test is used to determine the Breaking Force and Elongation of yarns. This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D13 on Textiles. ASTM D is by far the most common specification that is followed for determining the breaking strength, elongation, and energy of single strand textiles.
|Published (Last):||2 September 2014|
|PDF File Size:||11.69 Mb|
|ePub File Size:||17.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
Elongation in knot or loop tests is not known to have any significance and is not usually reported. Description Literature Contact Us This standard specifies the method for determining the tensile properties of yarns using the single-strand method, and helps determine the quality of the raw material while aiding in quality control of the finished product.
ASTM D2256 Tensile Properties of Yarns
Wet tests are made on flax yarns to detect adulteration by failure to show a gain in breaking force. Some modification of clamping techniques may be necessary for a given yarn depending upon its structure and composition.
Discover simpler and smarter testing with features such as pre-loaded test methods, QuickTest in seconds, enhanced data exporting: It provides an indication of the likely stretch behavior of garment areas such as asstm, elbows, or other points of stress.
A specially designed horn with 2d256 smooth finish and a contoured surface with a graduated cam allows for easy loading and a stress reduced clamping area on the specimen. Have a question about conducting the test for this standard?
Initial modulus is a measure of the resistance of the yarn to extension c2256 forces below the yield point. For directions covering the determination of breaking force of yarn by the skein method refer to Test Method D In any event, the procedure described in this test method for obtaining tensile properties must be maintained. These alternative rates may be used only by agreement between the parties concerned or when required in an applicable material specification.
Force range of 5 kN to kN 1, lbf tolbf Adjustable test space The most popular choice for static tension and compression tests These dual column testers are available in both tabletop and floor standing models. These are designed to permit predetermination of specimen length, and allow quick, convenient loading. The challenges of testing to this standard are: Force-elongation curves can be converted to stress-strain curves if the force is converted to unit stress, such as to centinewtons per tex, or pounds per square inch, or pascals, or ashm per tex, or grams-force per denier, and the elongation is based on change per unit length.
To prevent slippage in the clamps or damage as a result of being gripped in the clamps, special clamping adaptations may be necessary with high modulus yarns made from fibers such as glass or extended chain d2256.
A straight, B knotted, and C looped form. Bluehill LE aastm Basic Testing.
ASTM D D determines the tensile properties of monofilament, multifilament, and spun yarns, either single, plied, or cabled with the exception of yarns that stretch more than 5. As a minimum, use the samples for such a comparative tests that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly 2d256 in equal numbers to each laboratory.
Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest version of Bluehill. awtm
ASTM D Tensile Properties of Yarns by Single Strand Method – Instron
Next Checking to see if you are a returning visitor…. Special methods for testing yarns made from specific fibers; namely, glass, flax, hemp, ramie, and kraft paper and for specific products; namely, tire cords and rope, have been published: The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Load ratings from N to 5 kN 45 lbf to 1, lbf Designed for testing cord, yarn, fine winer, and similar specimens Rounded specimen mount resists specimen failure at the grip itself Pneumatic actuation for fast and easy specimen setup.
Give our test engineers a call today for help configuring the best test machine and accessories according to your standard.
Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience. We offer machines, apparatus, testers, tensile grips, test fixtures, clamps, holders, jigs, faces, jaws, extensometers, environmental and humidity chambers, furnaces, baths and custom solutions for unique applications.
The clamping mechanism can be activated either automatically or through a foot switch. This allows hands-free grip operation enabling the specimen to be held with both hands, for easy loading. The chord modulus is used to estimate the resistance to imposed strain. This standard specifies the method for determining the tensile properties of yarns using the single-strand method, and helps determine the quality of the raw material while aiding in quality control of the finished product.
Most yarns can be tested by this test method some modification of clamping techniques may be necessary for a given yarn depending upon its structure and composition. Email addresses can only contain letters, numbers and the following special characters: The breaking toughness is a measure of the work necessary to break the yarn. Test Methods Dand Specification D We are confident that we have what you are looking for.