The IGCT is a gate-controlled turn-off switch which turns off like a transistor but conducts like a thyristor with the lowest conduction losses. Figure 1 shows turn- off. Basic design rules and handling / application recommendations for IGCT Gate Units .. The connector X1 is specified in the corresponding IGCT data sheet. mm. Height h. ± mm. 41 mm. Width IGCT w. ± mm. mm. 1) Maximum rated values indicate limits beyond which damage to the device may occur.
|Published (Last):||20 March 2008|
|PDF File Size:||19.26 Mb|
|ePub File Size:||2.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
However, this steady-state value does not include the integrated effects of dynamic power buildup and adaptive grid response following the introduction of high-energy weapons and sensors.
Integrated gate-commutated thyristors (IGCT) | ABB
A generalized process for designing electric warships proposed by Doerry  consists of the following steps: Those implementations must be even more robust, however, as much of the information they process is classified. The driving force behind developing the convection model was to remove the user burden of specifying the convective coefficient, historically a difficult and computationally intensive task. The overall control of the inverter module contains a voltage control loop and a synchronous current regulator SCR.
As a result of the research, investigations can now be performed for studying the experimental power system setup of Purdue University to support the research for All-electric ship. The set of models provided herein is fairly extensive and adequate to serve as a basis for studying a variety of power system architectures. The goal of this architectural model is to develop an early-stage design tool capable of performing tradeoff studies on concepts such as AC vs.
In general the number of slots is large for distributed windings typically 6 per phase. The simulation model is fundamentally accurate for open circuit and load testing configurations. To make the capability available to as wide an audience as possible, the initial development will be made available to all users under Navy-sponsored programs.
The device’s control power consumption typically ranges from 10 – W. An important contributor to U. The rotor of a permanently magnetized synchronous machine can have the magnets applied either on the rotor surface or buried deep into the rotor.
Power electronics converters of the megawatt class need to be characterized regarding their capacitive, inductive, resistive and radiative coupling to the ground plane. Heat transfer by convection is a complicated process involving transfer of thermal energy through momentum and thermal gradients. Figure 1 shows the constant power load configuration. The PMSM are datasheef considered a linear device over its entire operating range of torque and speed, with practically linear speed-torque characteristic.
Furthermore, the guidelines and rules extracted through this task will be integrated into the S3D environment to datasheef applying well-established engineering principles to the automation of design evaluation.
And this has been successful. But such big machines are also employed in electrical drives for traction, rolling mills, mining etc. Such attributes are conveyed to the user through a custom dialog window.
So, the Department of Defense, as well as companies needing a competitive advantage, must find other solutions. Highlights in each of these areas are mentioned next. An error occurred and your inquiry could not be sent.
ESRDC | Electric Ship Research and Development Consortium)
In order to support these studies, the models catasheet forth include: As shown, this component consists of an input capacitor, a 3-phase fully controlled bridge converter, an output LC filter, and the control algorithms. When sufficient recommendations for change are made, they will be incorporated and a new revision will be released.
The second reason for the creation of highly simplified model is for the sake of computational speed, so that system simulations based on the component models will run at speeds compatible with the needs of exploring the system behavior under a large variety of conditions.
Please try again later or go to https: Please make vatasheet in the Word version of this document using track changes. This model wraps a model made by ACSL. First, a future surface ship must be robust and reconfigurable; with an optimal power distribution grid, ship sectors damaged during combat can be isolated from the rest of the grid, thus minimizing damage and prolonging the ship’s operability.
Then, several design variants were developed to explore datasyeet impact of alternative topologies and advanced materials. Secondly, reduced-order models are typically used. This effort will develop the Volterra Series technique into a comprehensive toolset that can provide a mathematically and physically rigorous and acceptable method to analyze nonlinear system classes, including high-power converters, with the added benefit dwtasheet model portability across other platforms and greater transparency with regard to model detail.
However, in contrast to the GTO, the turn-off protection network is optional. In retrospect, it is recommended that Simulink be used instead, preferably with a user defined igcy of the network interconnection equations, satasheet as described in .
The primary reason for this failure to completely model the systems was related to the choice of simulation engine.
First, throughout this report average-value models are used. However, the introduction of advanced electronics and pulsed-energy systems on a surface ship is not without consequences.
The project led to several enhancements of the design tool including new equipment library components, e. Terminals A and B are the electrical nodes.
The employed constant power load controller generates commanded inductor current. This promising approach has been investigated on a very limited set of components.
Dynamic Reconfiguration of Ship Power Systems – The RMS current is evaluated as the average of the square of the breaker current over a user specified time interval.
Integrated gate-commutated thyristors (IGCT)
The upgrade process was successfully completed and the PHIL facility has already been used for experiments including power conversion module testing and superconducting fault current limiters. This version of model is intended for simulation of linear circuits that were distributed only on two parts.
There was a problem with your request. This paper explores various power cable challenges for notional electric ship applications including future technology trends for shipboard power cables. The model reads values directly off the Excel spread sheet rather than from a saved data file.
A simple equivalent circuit model for EC capacitors can be established based on electrochemical impedance spectroscopy. A number of interface algorithms have been identified in the literature, such as those described in , for example.
IGCT (Integrated Gate-Commutated Thyristor)
The controls of the inverter have been developed to provide a means to control the speed or torque of a standard 3-phase induction machine.
Indicated below in the figure is the switch topology, based on which BoostConverter model no filter elements included is developed. I need service or support ABB Darasheet.