Buy PN ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 2: BASIC METHOD FOR THE. Buy NBR ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 2: BASIC METHOD FOR. DS/ISO ACCURACY (TRUENESS AND PRECISION) OF MEASUREMENT METHODS AND RESULTS – PART 2: BASIC METHOD FOR THE.
|Published (Last):||15 February 2017|
|PDF File Size:||6.60 Mb|
|ePub File Size:||10.43 Mb|
|Price:||Free* [*Free Regsitration Required]|
GSO ISO – Standards Store – GCC Standardization Organization
General principles and definitions – Part 2: Search all products by. The k values figure B-7 show that laboratories Unless otherwise specified, no part of this publrcation may be reproduced or utrlized In any form or by any means, electronrc or mechanical, rncludrng photocopyrng and mrcrofilm, wrthout permission in writing from the publisher.
This website is best viewed with browser version of up to Microsoft Internet Explorer 8 or Firefox 3.
You can buy this standard from any national standardization body. Draft International Standards adopted by the technical committees are circulated to the member bodies for 5725–2.
The purpose of the two-bottle system was to confirm the absence of the between-bottle variation. Therefore the Index j for the level has been omitted throughout. Basic methods for the determination of the trueness of a standard measurement method – Part 5: Ein grundlegendes Verfahren fuer die Ermittlung der Wiederhol und Vergleichspraezision von festgelegten Messverfahren.
As a result the experiment may have to be repeated to yield the expected preci- sion values. In order for the results of an experiment to be able to detect with a high probability see annex Cl a prede- termined magnitude of bias, the minimum number of laboratories, p, and test results, n, shall satisfy the following equation: Basic method for the determination of repeatability and re- producibility of a standard measurement method. Basic methods for the determination of repeatability and reproducibility of a standard measurement method Status: When a value for the bias of a measure- ment method is quoted, together with a test result obtained by that method, there is an implication that the same characteristic is being measured in exactly the same way.
The boxed points in figures B. Accuracy trueness and precision of measurement methods and results – Part 1: What action is to be taken concerning its publication?
There again, appropriate action should be taken by investigating these laboratories, or, if necessary, by tightening the protocol of the measurement method. However, for practical reasons, oso choice of the number of laboratories is usually a compromise between the availability of re- sources and the desire to reduce the value of 6, to a satisfactory level. Basic method for 7525-2 determination of repeatability and re- producibility of a standard measurement method – Part 3: The laboratory means and vari- ances for each of the five test materials are listed in table 8.
Intermediate measures of the precision kso a standard measurement method Specifies four intermediate measures due to changes in observation conditions time, calibration, operator and equipment within a laboratory. Please proceed with checkout.
BS ISO 5725-2:1994
These intermediate measures can be established by an experiment within a specific laboratory or by an inter Looking to purchase to post on your company’s Intranet? The faster, easier way to work with standards. They contain a digital watermark to protect the copyright.
Specifies four intermediate measures due to changes in observation conditions time, calibration, operator and equipment within a laboratory. Find Similar Items This product falls into the following categories.
IAccuracy trueness and precision of measurement methods and results – Part 1: Company organization, management and quality. IS0 consists of the following parts, under the general title Accuracy trueness and ixo of measurement methods and results: Do the results of the accuracy experiment justify the acceptability 57725-2 the measurement method for adoption as a standard? The analytical results are listed in tableB. Trueness is normally expressed in terms of bias.
Further regular testing is required to show that the labora- tory bias does ieo vary; the method described in IS0 may be used for this.
What action should be taken with respect to re- jected outlying laboratories? Basic methods for the determination of repeatability and reproducibility of a standard measurement method. The trueness of the measurement method can be investigated by comparing the accepted reference value with the level of the results given by the measurement method.
In the former case, the repeatability standard devi- ation, gr, and the reproducibility standard deviation, gR, will be used for the assessment of the trueness of the measurement method. Laboratory means and laboratory variances Lab.
Outliers and stragglers Level Lab. Methode de base pour la determination de la repetabilite et de la reproductibilite d’une methode de mesure normalisee.
If the reproducibility of the measurement method is poor, then it will not be practical to achieve a high degree of certainty in the estimate of the bias. Basic methods for the determination of the trueness of isi standard measurement method 1 Scope 1. Accuracy trueness and precision of measurement methods and results. C Derivation of equations The files of this standards is not available in the store right now.
Alternative methods for the determination of the precision of a standard measurement method – Part 6: Reference materials could be either a certified reference materials; b materials manufactured izo the purpose of the experiment with known properties; or c materials whose properties have been established by measurements using an alternative measure- ment method whose bias is known to be negligi- ble.